MACHINIST TOOLS - Magnetic Fixtures 

Adjustable Fixture Magnets
Hold and position sheet metal, round pipes, square, angled or flat stock.
Hold stock from the outside, leaving clearance for inside welds, or hold stock from the    inside for outside welds.
The Inside / Outside Angle Magnets are constructed from two independent rectangular        magnets for consistent, undiminished magnetic force when both sides are attached to    workpieces.
Adjustments range 30 to 270

4.7" 4.7" 26 lbs. MLA450 $20.41
6" 6" 33 lbs. MLA600 26.50

MLA450  &  MLA600

Adjust-O Angle Magnet Squares
Angle magnet squares with the convenience of On/Off switches.
Adjustable from 30 - 275 with two On/Off switches.
Precision machined flat surfaces and nickel/chrome body.
V-Groove surfaces securely hold round and square tubing, angle, and flat stock.

Max. Pull Force   110 LBS
Dimension           7-3/4 x 7-3/4 x 3-3/4"
Angles                45, 90



Adjust-O Magnet Squares
The original magnet squares featuring On/Off switches.
The fast & easy way to hold metal work pieces at 45 & 90.
Turn the magnet Off when setting up, turn On when you're ready to work.
Fast and safe set-up!
Ideal for round and square tubing, angle, and flat stock.
Easy to clean. Simply turn Off and wipe

Max. Pull Force   65 LBS
Dimension           4-3/8 x 3-3/4 x 1"
Angles                45, 90



Standard Magnet Squares - Multi-Angle
Holding at multiple angles while soldering, brazing, and welding
The compact size of the Mini Magnets makes it easy to pack, store, and carry for

   use anywhere!
Fully enclosed for easier cleaning.
Center hole for easy handling.



Max. Pull Force   85 LBS
Dimension           5-1/2
x 4-3/8 x 3/4"
Angles                30, 60, 45, 90




Mini Magnet Squares
At just 2-5/16" in height, Mini Magnets provid
e low profile holding of stock in tight,
  hard to reach areas.
Use as many as needed for light duty holding of stock at multiple points for greater    accuracy in fixturing with odd-shaped stock.
Perfect for use around the shop, and compact enough to carry along for use out in
   the field

Max. Pull Force   25 LBS
2-5/16 x 2 x 5/8"
Angles                30, 60, 45, 90


Corner Magnet
Create 90 corners by holding from the outside, providing you with an unobstructed
   area for inside tack welds.
One side corner "relief" provides clearance for tall lips.
Use the outer edges of the Corner Magnet for setting up materials at 60.

Max. Pull Force   30 LBS
Dimension           3-1/4
x 3-3/4 x 5/8"
Angles                30, 60, 45, 90



Adjustable Magnetic V-Pads Kit
Time saving magnetic tools for use in the shop & in the field.
Light duty & tight spot holding! Build, Hold, and Position Steel.
Hold and position round, flat, and square parts in light duty substructure applications!
Each V-Pad contains 4 rare-earth magnets

Max. Pull Force   18 LBS
Dimension           2 pc. Regular, 2 pc. Large




The better, faster way to hold tabs in place for tack welding!
Hold tabs, or any small metal pieces, parallel or perpendicular to the substructure.
The Adjustable Magnetic V-shape base adjusts for different shapes: round, flat,
   angle metal surfaces.

Dimension           4
x 3 x 1-1/4"


Grasshopper Welding Fixture
No other device can do what the Grasshopper does!
Use the "Welding Finger" to steady small parts, such as: bolts, nuts, and thin plates for     tack welding at odd angles with full welding clearance.
Brass Tip, Magnetic V-Pad Base with Maximum Pull Force 18 lbs
Safe and convenient!
Overall Length 7.5"
Width 2.5" x Height 3.5"



12" Snake Magnet
The Third Hand - Holds, Bends, Twists.
Comes complete with:
2 magnetic pads
1 spring clamp


Max. Pull Force   18 LBS



All Prices Subject To Change Without Notice 080119