TRUCK EQUIPMENT - Transfer Pumps and Accessories 

Rotary Hand Pump
The fill-Rite SD62 hand operated rotary vane transfer pump, with its smooth and easy turning handle, can deliver approximately 7.5 gallons of fluid per minute (100 revolutions).


• 7.5 gallon Per 100 revolutions
• Pail spout
• Compatible with Diesel, E15, Kerosene, B20 and Light Oils
• Tank or barrel mounting

 

SD-62
$
102.38

Piston Hand Pump with Steel Telescoping Tube and Nozzle Spout
Fill-Rite Piston Pumps have an aluminum body with a stainless steel liner. Providing smooth, continuous transfer of medium viscosity liquids, as well as oil, gasoline and diesel fuel. Pump easily mounts to a standard drum with 2 NPT threaded tank adaptor. 20 gallons per 100 strokes. Made in the USA
 

• 20 gallons per 100 strokes
• UL approved
• Aluminum body with stainless steel liner
• Anti siphon valve
• Pumps may be padlocked
• Pumps can be set up for reverse flow
• Telescoping steel pipe
• Nozzle spout

 

FR-152
$
233.80

DC Rotary Vane Pump Series 1200 12 Volt
This industry standard DC pump dispenses up to 15 GPM and has a draw that’s easy on the DC power source.
• Explosion-proof UL listed 1/4 HP motor with permanent magnet and ball bearings.
• Heavy-duty three-wire battery cable.
• Built-in check valve and strainer.
• 12' hose with static ground wire.
• Carbon rotor vanes.
• No foot valve required.
• 2” base for tank openings.
• Pump may be padlocked.
• Heavy-duty switch, thermal overload
• Telescoping steel suction pipe from 22” to 40”.
• Automatic bypass valve protection and junction box.
• Manual nozzle with nozzle boot that protects against dirt and contamination.

FR-1210G
$
389.00

Adaptor
Material: Cast–iron adaptor
Inlet/Outlet ports: 3/4" NPT
Nose outside thread: 1"–12 UNF

CIM-200H34
$
26.00

Filter
Designed for fuel dispensers & commercial fueling pumps.
Cellulose and Hydrosorb filters are for use with gasoline, diesel, biodiesel, or ultra-low sulfur diesel (ULSD)

CIM-300-30
$
12.50

Adaptor & Filter
Material: Cast–iron adaptor
Inlet/Outlet ports: 3/4" NPT
Nose outside thread: 1"–12 UNF
* * * * *
Designed for fuel dispensers & commercial fueling pumps.
Cellulose and Hydrosorb filters are for use with gasoline, diesel, biodiesel, or ultra-low sulfur diesel (ULSD)

CIM-COMBO
$
37.50

3/4 in. Manual Nozzle with Hook
• Compatible with gasoline and diesel
• UL/cUL listed
• 3/4 in aluminum nozzle

NO-75UMN11
$
38.00

3/4 in Auto Nozzle with Hook - Diesel
• Compatible with with diesel
• UL listed
• 3/4 in aluminum nozzle

 

NO-75DAU10
$
131.62

3/4 in x 12 ft Fuel Transfer Hose
• Dispense diesel fuel, gasoline, kerosene, and petroleum oils
• Neoprene exterior

 

FRH-07512
$
60.00

3/4 in x 20 ft Fuel Transfer Hose
• Dispense diesel fuel, gasoline, kerosene, and petroleum oils
• Neoprene exterior

 

FRH-07520
$
86.00

Vented Cap
This Fill-Rite Vent Cap allows excess pressure to vent to atmosphere, allowing electric or manual operated pumps to operate properly by not reducing flow rate when discharging fuel. It features aluminum construction with a cast iron threaded base; 2" NPT male thread and fits all auxiliary or transfer tanks with 2" Outlet Port

 

FRTCB
$
53.40

All Prices Subject To Change Without Notice 122815